Instructions hp StorageWorks Enterprise Virtual Array Updating Product Software VCS Product Version: 3.025 HP StorageWorks Command View EVA Version: 3.3.

****************************************************** What Ive done, is to INFORM the costumers using an EVA4400/6400/8400, that when pushing up the XCS to this version, it will cause DOWNTIME on all SAN attached stuff. Ok, I work in this order. Reading logs from EVA 2. Cara Meinstall Printer Canon Mp230 Series Di Windows 8.

Reading a lot of information from HPs Connectivity documents 3. Upgrading all san switches to latest available firmware 4. Upgrading Command View Eva to 9.1 (If they use a Management Appliance server) 5. Upgrading the WOCP, HP EVA Management board to latest firmware 5:a Check firmware matrix before, so that the current XCS is supported with the latest WOCP firmware. 5:b The firmware for the WOCP is stored under the Command View EVA 9.xxx install CD or folder, its called: ABM.pkg.

5:c Now when you updated the firmware on the WOCP, and the WOCP has rebooted, do not log in! Wait at least for 15 min, it will save you time. 'IMPORTANT:The management module will restart on completion of this update. Allow up to 15 minutes to re-establish a browser connection. Do not reseat, restart, or reset the management module during this time if you are unable to reconnect from your browser.

After the management module restarts, it may exhibit slow response time for about 5 to 10 minutes while gathering array information and completing background processes.' To log on to the WOCP, use To Log on to the Management boards Command View EVA: use: If everything goes as planned, you will be able to proceed with upgrading the EVA4400, after reading some more EVA logs:). WOCP Release notes: Release Notes: mmp-0001.3000-CR03D8 ============== Release Notes: This firmware package will upgrade the management module to version 0001.3000, which includes HP Command View EVA Array Based Management. Before installing version 0001.3000, the HP StorageWorks Enterprise Virtual Array must first be running a minimum of version 09006000.

While the firmware is being upgraded DO NOT reseat, restart, power-cycle, or reset the management module. Vw T5 Transporter Bedienungsanleitung Pdf Printer. The management module will automatically restart upon completion of this upgrade. Allow up to 15 minutes for the upgrade to complete and then browse to the upgraded WOCP on port 2373. IMPORTANT: If upgrading the management module from firmware older than version 0001.1000, the progress timer displayed on the WOCP during this upgrade will run down before the upgrade has actually completed. When the timer expires, the browser will attempt to reconnect to the WOCP at port 2372. However, the upgrade has not completed and the management module has not yet restarted with the new firmware. Allow up to 15 minutes for the upgrade to complete and then browse to the upgraded WOCP on port 2373.

During this period DO NOT reseat, restart, power-cycle, or reset the management module. When the upgrade has completed successfully, the HP Command View EVA user interface will reside on port 2372, in place of the WOCP. The new WOCP user interface will then reside on port 2373. • //storage.zolkoo.com/#post27. Posted by 2009-09-17 10:55:18 Im posting this as usuall just to remember the stuff. So I have an EVA5000 with a vcs 3110, and a EVA8100 with XCS 6220.

The costumer has ordered an CA licens, valid for 90 days and its installed at on to the EVA8100. EVA 5000 has a full licens of CA installed. The sanswitches are cisco. Here we zoned the SAN management server with both EVA´s in the same zone, so that SAN management zone has a meberlist of: san management_alias, EVA5000_CTRL1_alias, EVA5000_CTRL2_alias, EVA8100_CTRL1_alias and EVA8100_CTRL_alias. Now, I can start up the Command View EVA utilitiy, I use CVE 9.1. Go to the EVA5000 (this is SOURCE), go to DR Replication, Add a new Vdisk for replication, and point out the new SAN in my case EVA8100.